
Blank System modules
As in every OK-VISE Fixturing Concept system, the basic modules in the Blank System are clamp, stopper, side guide and riser block modules.
To resist the clamping and machining forces, a pocket should be machined to the blank plate. Pictures of the pockets are available in the installation instruction.
Clamp modules ( KCD- dual directional )
Code | Dim. | STEP |
KCD-DS1 | ![]() | X |
KCD-DS2 | ![]() | X |
KCD-DR1 | ![]() | X |
KCD-DR2 | ![]() | X |
In most cases, code format is KCD-sjn, where s corresponds to a clamp size (B or D), j is a jaw type (Serrated, Smooth) and n is a plate type.
KCD-DS2
KCD-BR2
Clamp modules ( KCS- single directional )
Code | Dim. | STEP |
KCS-DS1 | ![]() | X |
KCS-DR1 | ![]() | X |
KCS-DES1 | X | |
KCS-BR3 | ![]() | X |
In most cases, code format is KCS-sjn, where s corresponds to a clamp size (B or D), j is a jaw type (Serrated, Smooth) and n is a frame type.
Almost all other jaw combinations are also available. For example, in KCS-DES1 model, E stands for a self-aligning jaw and S - for a smooth jaw.
KCS-DX modules recomended maximum clamp tightening moment is 70Nm. Maximim force is 30KN.
For extremely compact design, types like KCS-BR3 are recommended. Please note that in this case fixture plate must be machined also from the bottom side (see instruction).
KCS-DR1
KCS-DT1
KCS-DES1
KCS-BR3
There are also "A" models that are optimized specially for robotic loading of workpieces, for KCS-DR1A
Stopper, smooth jaw (KS-Sx)
Code | Dim. | STEP |
KS-S1 | ![]() | X |
KS-S2 | ![]() | X |
KS-SO1 | ![]() | X |
In most cases, code format is KS-Sx, where S corresponds to a smooth jaw type and x is a stopper type.
KS-S1
KS-SO1
Stopper, serrated jaw (KS-Rx)
Code | Dim. | STEP |
KS-R1 | ![]() | X |
KS-R2 | ![]() | X |
KS-R3 | ![]() | X |
In most cases, code format is KS-Rx, where R corresponds to a serrated jaw type and x is a type.
KS-R1
KS-R2
Stopper, diamond jaw (KS-Dx)
Code | Dim. | STEP |
KS-D1 | ![]() | X |
KS-D2 | ![]() | X |
KS-D3 | ![]() | X |
In most cases, code format is KS-Dx, where D corresponds to a diamond jaw type and x is a base type.
KS-D2
Low stopper, serrated jaw (KS-R6)
Code | Dim. | STEP |
KS-R6 | ![]() | X |
This stopper type is normally embedded 6 mm in the base plate
Uses M6 bolt.
KS-R6
Blank System riser blocks (KP-)
Code | Dim. | STEP |
KP-1 | ![]() | X |
In most cases, code format is KP-n, where n is a type.
KP-1
Blank System side quides (KG-)
Code | Dim. | STEP |
KG-1 | ![]() | X |
KG-2 | ![]() | X |
In most cases, the code format is KG-n, where n is a guide type.
KG-1
KG-2